Ultrasonic Marine System

Easy to install and operate.

Using experience gained in the military and aviation industries, the Ultrasonic Marine Antifouling System is designed to be very effective yet competitively priced and easy to install.

Easy Installation

Installing the USM system is a simple process that can confidently be taken on by anyone who enjoys working on their own boat or your local marine maintenance facility. The components are ready to be attached and hooked up right out of the box. Complete instructions are included.

The Transducers are attached along the inside surface of the hull using marine adhesive. No holes are needed in the hull.

  • Designed and assembled in the USA.
  • Our experience in ultrasonic technology was developed having been a supplier for industrial and aerospace transducer markets.
  • Designed & manufactured to military standards. Built to the same standards as military products which have included items for Awacs, B2, Apache & Chinook helicopters, C130 and nuclear submarines.
  • Safely operates without interference to other nearby equipment. Exceeds FCC requirements.
  • Low power consumption, typically under 4 watts per transducer.
  • Active transducers to eliminate interference to other equipment.
  • Suitable for fiberglass aluminum and steel hulls.
  • Power control programmed to gradually reduces transmitted power to protect battery if battery voltage falls during operation.


Installed System
Installed USM System and mounted transducer (detail)

1 Year Warranty Plus 90 Day Satisfaction Guarantee.

If after installing and using our system for 90 days, you’re not completely satisfied, you can return the control box, cables and transducers and we’ll refund the cost of the system (excluding installation costs).
Components and Technical Details

Each system includes a Control Box and 1 to 4 Transducer units depending on the size of the vessel. The number of Transducers needed depends on the size of the boat. See our guide below.

System includes Transducer cables and Control Box power cables.
Control Box AF101C  (Box size 4.3"x4.3"x2.7")

  • LED light shows unit operation status.
  • Each Control Box has outputs for up to 4 transducers. Larger vessels needing more than 4 transducers will require extra Control Boxes.
  • Control Boxes are water resistant and can be installed in the most convenient location.
  • Includes inputs for 12V ships supply. Optional 110/230 volt AC power cord to run to shore supply is available.
  • The system automatically switches over to the vessel's battery when disconnected from shore supply.
  • Power is automatically gradually reduced if the battery voltage becomes low and is switched off at a determined point to protect the battery.
  • Can be run off solar supply if available. Supply should be rated at least 40 watt output or more depending on the number of transducers in the system.

​Input voltage 11.5V to 30.5V DC
Average consumption 4 watt maximum per transducer.
Operation -35 to +50 degrees C
IP66 environmental protection.
Size 11 x 12 x 6.7 cms

Transducer  (Size 2.8" diameter by 4.2" height)

​Transducer is to IP68 & the Control box to IP66 environmental protection.

Care has been taken to exceed the requirements of the CE specifications to avoid electromagnetic interference to other equipment nearby.

The active transducers contain all the high voltage drive circuitry. This eliminates interference to other equipment through radiation from a long cable from the control box

IP68 environmental protection.
Operation -35 to +50 degrees C
Size 10 x 5.7 cms
Order codes:
Control box AF204C
Transducer AF201T (State number required)
Power supply AF200PS (For 110V/230V AC OPERATION)

  • LED light shows when unit is operating.
  • Exceeds FCC requirements.
Picture
Inside of Control Box
Picture
Transducer bottom
Picture
Typical number and location of transducers according to boat size.
Ideal system depends on hull style, length and local fouling levels. Contact us for advice on best system for your vessel.
​
Twin screw vessels should preferably use an extra transducer.

Wave goodbye to barnacles.

Call 216-533-1410 today for more information or purchase the USM System here.
Email Us or see more company details here.